DITL_28_SC_Loopback Test.txt
Items: (11 entries)
  0:
    Bounds: x1=357, y1=199, x2=457, y2=220
    Type: 4
    Info: 'Cancel/Quit'
  1:
    Bounds: x1=363, y1=243, x2=451, y2=267
    Type: 4
    Info: 'Run Tests'
  2:
    Bounds: x1=250, y1=221, x2=335, y2=238
    Type: 8
    Info: '--'
  3:
    Bounds: x1=29, y1=77, x2=480, y2=127
    Type: 8
    Info: '¥  For accurate results, EtherLan SC must be connected to a properly terminated thinnet cable or Medium Attachment Unit, depending on configuration, before running the tests. '
  4:
    Bounds: x1=29, y1=141, x2=480, y2=191
    Type: 8
    Info: 'WARNING:  Running these tests will briefly take EtherLan SC off of the Ethernet network.  Do not run these tests if you are logged onto a network server.'
  5:
    Bounds: x1=250, y1=248, x2=335, y2=264
    Type: 8
    Info: '--'
  6:
    Bounds: x1=250, y1=274, x2=336, y2=290
    Type: 8
    Info: '--'
  7:
    Bounds: x1=51, y1=274, x2=238, y2=290
    Type: 8
    Info: 'Thinnet Transceiver or MAU:'
  8:
    Bounds: x1=64, y1=248, x2=239, y2=264
    Type: 8
    Info: 'Serial Network Interface:'
  9:
    Bounds: x1=34, y1=221, x2=238, y2=238
    Type: 8
    Info: 'Network Interface Controller:'
  10:
    Bounds: x1=29, y1=16, x2=479, y2=65
    Type: 8
    Info: '¥  Clicking on the "Run Tests" button will run three separate loopback tests on the network hardware in the EtherLan SC box and its connection to the network.'

DITL_18_Set Address.txt
Items: (12 entries)
  0:
    Bounds: x1=369, y1=184, x2=451, y2=205
    Type: 4
    Info: 'No Change'
  1:
    Bounds: x1=363, y1=224, x2=463, y2=246
    Type: 4
    Info: 'Set to Default '
  2:
    Bounds: x1=369, y1=258, x2=455, y2=281
    Type: 4
    Info: 'Change'
  3:
    Bounds: x1=17, y1=5, x2=472, y2=55
    Type: 8
    Info: '¥  Specifying an address in the "Change Address to:" edit area and clicking on "Change" will put an alternate Ethernet address in your System File.'
  4:
    Bounds: x1=40, y1=187, x2=216, y2=205
    Type: 8
    Info: 'Current Ethernet Address: '
  5:
    Bounds: x1=50, y1=228, x2=216, y2=246
    Type: 8
    Info: 'Built-In Default Address: '
  6:
    Bounds: x1=87, y1=262, x2=216, y2=280
    Type: 8
    Info: 'Change Address To:'
  7:
    Bounds: x1=221, y1=187, x2=325, y2=205
    Type: 8
    Info: ''
  8:
    Bounds: x1=222, y1=228, x2=326, y2=246
    Type: 8
    Info: ''
  9:
    Bounds: x1=17, y1=121, x2=475, y2=172
    Type: 8
    Info: 'WARNING:  The default address built into EtherLan SC is guaranteed to not conflict with other devices on your network.  Don't change it without a good reason. '
  10:
    Bounds: x1=223, y1=262, x2=324, y2=278
    Type: 16
    Info: ''
  11:
    Bounds: x1=16, y1=63, x2=474, y2=113
    Type: 8
    Info: 'Note:  Unlike the default address, the new address will not be "hard-coded" in the EtherLan SC unit.  It will be read from your System File and sent to the unit each time your Macintosh boots up.'

DITL_8_SC_NoDriver.txt
Items: (2 entries)
  0:
    Bounds: x1=112, y1=119, x2=172, y2=139
    Type: 4
    Info: 'OK'
  1:
    Bounds: x1=34, y1=64, x2=275, y2=114
    Type: -120
    Info: 'EtherLan SC Setup was not able to open the EtherLan SC driver in your System file.'